Dd wrt dhcp options

Dd wrt dhcp options

Setting a static ip address using static dhcp lease on dd

In the Additional Config area, you can also add more VPN servers (if the first server is not available connection will be set up to the next server in the list”). It’s best to use both the hostname and IP address defined at the start of the VPN configuration file. Consider the following scenario:
Put the following command for 192.168.1.0/24 (default IP addresses range for users; you can see the current IP addresses range for Network Setup at Setup Basic Setup) to enable traffic forwarding only via VPN network interface:

Dhcp forwarder for jabber clients

This may sound ridiculous, but I have a DD-WRT (micro) router in my network that serves as a switch and a WAP, with my cable modem acting as the DHCP server. In an effort to correct the setup, I set the router to DHCP forwarder, which allowed it to function properly. The issue now is that I am unable to connect to the router in any way in order to add mac addresses to the WAP access list.
Aside from that, I would suggest keeping it on dhcp server and disabling the dhcp server instead of using it as a dhcp forwarder. Then check the box to “Assign WAN Port to Switch” and set the WAN type to Disabled.
In the basement, I have my main wifi router and a couple of servers connected by ethernet cables. Wifi, of course, is available anywhere. I have an office upstairs, and running ethernet down to the basement is impractical. I can’t add wifi to some computers, so I link them to a second router (the dd-wrt’d machine in client bridge mode), which connects to the main router via wifi (on the same SSID, so they’re on the same LAN). The client bridge does not have DHCP services; instead, it routes requests to the main router.

Dd-wrt dnsmasq setup and local dns

On an older Linksys WRT54G v8 wireless router, I’m using DD-WRT. All works fine before I try to do some more precise routing. This does not seem to be related to DD-WRT, and it may be a simple network paradigm that I am overlooking.
I’m sure there are many ways to do this with DD-WRT, but I went with the simplest option and configured the WAN port to receive an IP from the main network’s DHCP server, which is on the 10.0.0.0/24 network. This element works flawlessly (currently, the IP address is 10.0.0.84 on the WAN port).
However, I am unable to connect to the internet. I can ping the LAN/WLAN subnet at 192.168.200.1 without issue while linked wirelessly, and I can also ping 10.0.0.84 (WAN interface) without issue. Anything beyond that, however, does not respond to ping.
I’m still struggling to get anything to work here. What am I overlooking? I’ve even tried Dynamic routing since what I’m doing is basically a plug-and-play process on every standard network with this configuration, but it’s still not working.
Next, reboot your DD-WRT router. They can be glitchy at times. Do you have the right gateway and subnet settings for your 10.0.0.0/24 network in your DD-WRT WAN setup? Static WAN settings get a thumbs up. You can also reset DD-WRT to factory settings and then reconnect it in the same manner.

Dd-wrt client mode setup

Static DHCP (also known as DHCP reservation) is a useful function that allows your router’s DHCP server to allocate the same IP address to a specific device on your LAN at all times. To be more precise, the DHCP server assigns this static IP to each NIC on your LAN’s unique MAC address. When your machine starts up, it demands an IP address from the router’s DHCP server. The DHCP server recognizes your device’s NIC’s MAC address and assigns it a static IP address. (It’s also worth noting that each reserved IP address must currently be unique.) As a consequence, even if the system is designed such that only one interface is active at any given time, one cannot reserve the same IP address for both the wired and wireless interfaces.)
If you want an interface to have the same IP address all of the time, you’ll need static DHCP. This function is useful if other people on your LAN know your IP and use it to access your PC. It is often needed for some programs. In conjunction with Port Forwarding, static DHCP should be used. If you want to forward an external WAN TCP/UDP port to a port on a server within your LAN, you’ll need to assign that server a static IP address, which you can do with Static DHCP.

About the author

admin

View all posts